How to polish the ring

1. First of all, rough throws. Rough polishing is to throw off the soda marks, clamp marks, diamond marks, burrs, and black oxide layers left on the surface of the jewelry metal bracket. Make the lines smooth. However, it is not too large and polished. For example, leaving a depression on the surface of the jewelry bracket will be difficult to restore its appearance. Rough throw is the basis of medium and fine throws. If it is not required, it will affect the later polishing, which will directly affect the quality of the jewelry.
. Then turn on the polishing motor, use the motor axis rotation force to rotate with polished bristles (ancestral brushes), and after the brush is tightened On the brush, you can polish.
3. The brush is mainly polished on the countertops of the inlaid jewelry, the main and auxiliary edge, and the gaps of the flower jewelry, as well as the outside of the ring. During the operation, the first thing to pay attention to is to evenly polish the wax on the brush. The polishing force should be appropriate. It cannot cause excessive force to cause jewelry deformation, paw, loose claws, or even stones. There are still residual marks, abrasions, etc. All jewelry should be polished thickly, and the polishing should be repeatedly polished.
4. If you polish the ring, you should also use the inner ring of the polished rings with a pill core rod. Select the appropriate velvet rod as required. Before polishing, you must apply a green polished wax to the rings. When throwing, pay attention to the contact surface of the villuk core and ring, that is, the ring cannot be put in the pill core stick too deep, and keep the polishing contact surface of 1/3 of the inner ring arc. The polishing angle surface is too small, and the work efficiency is low; the contact surface is too large, and it is very inconvenient to change the polishing level. Moreover, due to the large friction resistance, it is difficult to get stable and polished. The shape of the ring or jewelry.
5. Pay attention to the bristles and cloth wheel wax when coarse polishing, but you cannot apply too much on the wax to avoid the polishing wax rubbing and heat it to melt it on the surface of the jewelry. Signs and hemps, etc., will affect the quality of the thick polishing of jewelry, and bring difficulty to fine polishing, and even lead to re -throwing.
6. The polishing method of polishing operator will also affect the polishing quality. If the polishing operation method is incorrect, it is impossible to throw jewelry. Generally speaking, when polishing, try to make the jewelry parallel with the polished cloth wheels, hold the jewelry with both hands and move the direction of the cloth wheel from top to bottom. Polishing must uniformly complete the nationwide of the jewelry at one time, and each part must be thrown in place. The polishing method is incorrect, and the polished jewelry is easily taken off by bombing on the polishing wheel of high -speed flying. For example, the polished jewelry is small (such as chest pendant and earrings), you can prepare a hook made of a metal wire, keep the jewelry polishing in the left hand, and prevent jumping polishing and forcelessness when polishing. If there is a jumping phenomenon, it may be that the polishing wheel is not in the axis heart, or the polishing cloth wheel may not be round. It is more likely to be a gesture problem. Finding the reason is to solve the problem.
7. Some of the more difficult alloy jewelry, because the metal toughness of making jewelry is tough on the soft metal to lit with a stranding phenomenon, it is not easy to throw the metal surface. The jewelry should be polished as much as possible. The method of polishing is basically the same as the rough throw. The bristles and yellow cloth wheels are still polished. The medium throwing is only different. Oxides). Mid -polishing is to operate according to the method of rough polishing, and polishing the jewelry from beginning to end.
8. After any jewelry is thick, it must be polished to make the surface of the metal jewelry more smooth. The fine throw is further polished on the basis of thick and medium throwing, making the surface of the jewelry more flat and smooth, and achieved to achieve the surface of the jewelry. Mirror reflective effect. However, its polishing and rubbing contact surface is small. When polishing, not only is small and uniform, but must be fully polished on the surface of the jewelry. The specific method is to use a fine white cloth and red polishing wax. , Then polish the side of the jewelry, the corner. If you polish the ring, apply red wax on the ring rod on the ring rod to the inner circle of the ring. Then, the positive flower shoulder of the polishing ring finally polished the sides and outer circles of the jewelry.
9. Jewelry jewelry is rough, medium polishing and fine polishing 3 times. It should be said that the surface of the jewelry can reach the level of smoothness. But sometimes because of the rough grinding, there are still large traces and scratches on the surface of the jewelry. It is difficult to remove it by polishing. There is also the tattoos that are drained under the surface of the jewelry during polishing, which not only affects the smoothness of the jewelry but also affects the quality of the jewelry. After scanning sandpaper, then polishing. There is a hemp point on the surface of the jewelry. It must be replenished.

Ring polishing requires professional tools, especially the re -polishing of the finished product. Be careful not to hurt the inlaid gem when polishing. It is recommended to find a professionals to deal with it.

54654 店 Doctor doctors of non -staple food shops